 |
 |
 |
|
TruFiber 3" Cowl Fiberglass Heat Extractor Hood For 2007 - 2009 Ford Shelby GT500
Get a boost in style and performance with a fully functional heat extractor hood from TruFiber. Each hood is specifically designed to remove heat from the engine bay for optimum performance and maximum cooling capabilities. TruFiber heat extractor hoods are made with high quality hand-laid fiberglass and topped with a smooth gel coat finish. Featuring a one piece underside shell for added structural integrity, TruFiber hoods offer exceptional durability and a long lasting life span. High performance styling, excellent fitment, and fully functional design has made TruFiber custom fiberglass hoods a must have for all performance enthusiasts.
- Custom Styling & Enhanced Appearance
- Fully Functional Heat Extractor Design
- Made From Top Quality Hand-Laid Fiberglass
- Excellent Fitment & Durable Design
- 3" Inch Cowl Height
TruFiber hoods are specifically designed for each vehicle to provide optimum fitment and maximum air flow. Each hood is made from high quality hand-laid fiberglass and topped with a smooth gel coat finish. Fully functional design, durable construction, and high performance styling have made TruFiber custom hoods an excellent choice for those wanting functional performance and aggressive styling.
Product Application Chart
| YEAR | MAKE | MODEL | TRIM |
| |
| | | 2007 | Ford | Mustang | Shelby GT500 | | 2008 | Ford | Mustang | Shelby GT500 | | 2009 | Ford | Mustang | Shelby GT500 |
*Fits Shelby Models Only
IncludesThis TruFiber heat extractor hood includes the hood only. Your factory hardware, hinges, and latch will be needed for installation.
Product Notes Trufiber hoods come unprepped and unpainted. Typical prep work may include - but not limited too - sanding, priming, and painting. Professional installation recommended.
Damage Insurance Policy
Damage Insurance is included on the hood during shipping, but only to your door. After you accept and sign for the package, there is no damage insurance. Please be sure to carefully inspect the hood for damages before accepting delivery. If the hood is damaged, refuse the shipment and sign "damaged" on the signature area of the shipping receipt.
TF10024-A49-3KR
2007 - 2009 Ford Mustang Shelby GT500 3" Cowl Fiberglass Heat Extractor Hood - TruFiber
Ships From:
Manufacturer - TruFiber
Shipping Method:
Ground Freight Shipping - Signature Requested For Delivery
Installation Notes:
Replacement body panels should always be installed by a certified autobody shop. Fiberglass hoods come unprepped and unpainted. Prep work will be required for installation. Typical installation procedures may include - but not limited too:
- Installing your factory hardware, hinges and latch from your original hood to the new hood.
- Adjusting the latch assembly, hinges, supports, and surrounding body panels for proper fitment.
- Sanding down high spots, filling in low spots, and trimming excess material.
- Drilling holes for windshield washer nozzles, clips, fluid lines, or various hardware.
- Installing hood pins for additional safety and proper installation (required).
- Installing a heat shield or insulation pad (required).
- Removing factory hood struts/shocks (if applicable) to prevent bending, warping, cracks or other damages.
- Sanding, priming, painting, and clear coating.
- Installation procedures may vary, professional installation recommended.
- Always be sure to test fit your parts before modifying them. Modifying your parts may void the manufacturers warranty.
California Proposition 65 Warning
WARNING: This product may contain chemicals and/or compounds known to the state of California to cause cancer and birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov
Manufacturer:
TruFiber
Manufacturer Part Number:
TF10024-A49-3KR
Product Category:
Ford Shelby GT500 Hood
|
|
|
 |
|
 |
|